[Macchiato] RHEL 8 fails to boot with UEFI 18.09.0

[Andrew Elwell]

Hi Folks,

Thought I'd try RHEL for Arm 64 on my macchiatobin doubleshot, but
although the installer completed OK, the first reboot after a yum
update is failing to boot.

Console log:

OR flash 1 (0x32)
Found valid image at boot postion 0x000
lNOTICE:  Starting binary extension
NOTICE:  SVC: SW Revision 0x0. SVC is not supported
mv_ddr: mv_ddr-armada-18.09.2-g99d7725 (Oct 29 2018 - 23:32:10)
mv_ddr: completed successfully
NOTICE:  Cold boot
NOTICE:  Booting Trusted Firmware
NOTICE:  BL1: v1.5(release):v1.5-219-g711ecd3 (Marvell-armada-18.09.4)
NOTICE:  BL1: Built : 23:32:27, Oct 29 2018
NOTICE:  BL1: Booting BL2
NOTICE:  BL2: v1.5(release):v1.5-219-g711ecd3 (Marvell-armada-18.09.4)
NOTICE:  BL2: Built : 23:32:35, Oct 29 2018
BL2: Initiating SCP_BL2 transfer to SCP
NOTICE:  SCP_BL2 contains 5 concatenated images
NOTICE:  Skipping MSS CP3 related image
NOTICE:  Skipping MSS CP2 related image
NOTICE:  Load image to CP1 MSS AP0
NOTICE:  Loading MSS image from addr. 0x40265f4 Size 0x1ad8 to MSS at 0xf4280000
NOTICE:  Done
NOTICE:  Load image to CP0 MSS AP0
NOTICE:  Loading MSS image from addr. 0x40280cc Size 0x1ad8 to MSS at 0xf2280000
NOTICE:  Done
NOTICE:  Load image to AP0 MSS
NOTICE:  Loading MSS image from addr. 0x4029ba4 Size 0x4a40 to MSS at 0xf0580000
NOTICE:  Done
NOTICE:  BL1: Booting BL31
lNOTICE:  BL31: v1.5(release):v1.5-219-g711ecd3 (Marvell-armada-18.09.4)
NOTICE:  BL31: Built : 23:32:47, Oct 29 2018

Armada 8040 MachiatoBin Platform Init

Comphy0-0: PCIE0         5 Gbps
Comphy0-1: PCIE0         5 Gbps
Comphy0-2: PCIE0         5 Gbps
Comphy0-3: PCIE0         5 Gbps
Comphy0-4: SFI           10.31 Gbps
Comphy0-5: SATA1         5 Gbps

Comphy1-0: SGMII1        1.25 Gbps
Comphy1-1: SATA2         5 Gbps
Comphy1-2: USB3_HOST0    5 Gbps
Comphy1-3: SATA3         5 Gbps
Comphy1-4: SFI           10.31 Gbps
Comphy1-5: SGMII2        3.125 Gbps

UTMI PHY 0 initialized to USB Host0
UTMI PHY 1 initialized to USB Host1
UTMI PHY 2 initialized to USB Host0
Succesfully installed protocol interfaces
Detected w25q32bv SPI NOR flash with page size 256 B, erase size 4 KB,
total 4 MB
ramdisk:blckio install. Status=Success

Tianocore/EDK2 firmware version MARVELL UEFI 18.09.0
Press ESCAPE for boot options XhcCheckUrbResult: BABBLE_ERROR! Completecode = 3
XhcControlTransfer: error - Device Error, transfer - 8
...Failed to set MokListRT: Invalid Parameter
Could not create MokListRT: Invalid Parameter
Something has gone seriously wrong: import_mok_state() failed
: Invalid Parameter
ERROR:   a8k_system_off:  needs to be implemented
lPANIC at PC : 0x0000000004023208



>From a quick search of MokListRT, it may be I need to put something
else on the EFI partition and/or update firmware.
Any suggestions?

Also, unrelated I see the forums have been made useless by spambots :-/